Használati útmutató BSS Audio Soundweb 9008

Olvassa el alább 📖 a magyar nyelvű használati útmutatót BSS Audio Soundweb 9008 (15 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/15
Installation Guide
Soundweb
TM
2
9008 Installation Guide
Regulatory Information
An example of this equipment has been tested and found to comply with the following
European and international Standards for Electromagnetic Compatibility and Electrical
Safety:
Emissions (EU): EN55013 (1990)
Generic Immunity (EU): EN50082-1 (1997)
Electrical Safety (EU): EN60065+A11 (1993)
Electrical Safety (USA): UL6500/ETL (1996)
Electrical Safety (CAN): CAN/CSA-E65/ETLc (1994)
Radiated Emissions (USA): FCC parts 15 Class B
For continued compliance with international EMC regulations, it is important that all
cables be screened, and connected as follows:
Audio cable screens to their 9008 connector ground.
Control cable screens to the ground screws adjacent to the connector.
Network cables should be of type CAT. 5
IMPORTANT SAFETY INFORMATION
Do not remove covers.
No user serviceable parts inside - refer servicing to qualified service personnel.
This equipment must be earthed.
It should not be necessary to remove any protective earth or signal cable shield
connections to prevent ground loops. Any such disconnections are outside the
recommended practice of BSS Audio and will render the EMC or safety certification
void.
Mechanical Installation
If the unit is likely to undergo extreme vibration through extensive road trucking and
touring, it must be supported at the rear and/or sides to lessen the stress on the front
mounting flange. Use either a ready-built rack tray or mount the 9008 unit between other
units. Damage caused by insufficient support is not covered by the warranty.
To prevent cosmetic damage to the front panel finish, use protective plastic cups under
the rack mounting bolts.
Soundweb
TM
9008 Installation Guide
3
Front Panel LED Functions
DSP Clip
Illuminated = indicates that the processed signal is clipping internally.
Network
Sync
Steady = indicates the presence of one or more valid network connections.
Flashing = there is a problem with the incoming network signal - check connections and/
or possibly the maximum cable length has been exceeded.
Activity
Flashing Yellow = indicates data transfer. The flashing is not regular, but dependent on
the rate of transfer.
Flashing Red = indicates bad data and is usually caused by network faults. Check
network connections, see Rear Panel details.
Power
Illuminated = indicates that the power supply is functioning.
Flashing = the network is initialising. If the led continues to flash for
more than a few seconds, there is a cabling fault - either a double ring
error or a problem with one of the cable connectors.
Steady = this unit has become the clockmaster for the network.
Off = this unit is clienting to an external master clock.

Termékspecifikációk

Márka: BSS Audio
Kategória: nincs kategorizálva
Modell: Soundweb 9008

Szüksége van segítségre?

Ha segítségre van szüksége BSS Audio Soundweb 9008, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva BSS Audio

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025