Használati útmutató BOYA BY-WXLR8 Pro

BOYA mikrofon BY-WXLR8 Pro

Olvassa el alább 📖 a magyar nyelvű használati útmutatót BOYA BY-WXLR8 Pro (2 oldal) a mikrofon kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/2
Press + & -
to unlock
5
4
5
4
LCD will be locked automatically in 30 seconds
Long press bottoms “+” and “-“ to unlock.
27 28 29 30 31 32
7. SET button
Press to change and enter display parameters.
For details, please see “How to set up channel, VOL, STEREO
and MONO” on page 24.
5. LCD display
8. Battery compartment
Accommodates two AA batteries.
6. + (+ selection)/ – (- selection) buttons
Press these buttons to set the transmission channel, or
attenuation level of the input signal.
9. Power/Mute button
Function Operation
Power ON
Power OFF
Mute ON
Mute OFF
Long press button
Long press button until it turns o
Short press button
For more details about LED indicator, please refer to “Power LED
on page 30.
3) The pwer LED of BY-WXLR8 Pro blinks red when mute on.
Only works with XLR dynamic micrphones or battery-powered
condenser microphones.
BY-WXLR8 Pro
Plug-on Transmitter
1. Audio XLR input connector
Connect a microphone or a line output connector of an audio
mixer, etc.
2. Power LED
1) The power LED glows blue when the unit is on.
2) The power LED of transmitter glows red when low power.
3. Knurled ring
4. Line In
LCD Display Operation Guide. Installing Batteries
The transmitter is each powered by two AA batteries. To install
batteries, please follow these steps:
1. Slide the battery cover to release the lock and open the battery
compartment.
2. Insert two new AA batteries into the battery compartment by
matching their polarities to the indications inside the compartment,
and then close the cover.
To attach a microphone or a XLR cable
Microphone or XLR cable
Knurled ring
Push the microphone or cable connector into the XLR audio
input jack of the BY-WXLR8 Pro, then turn the knurled ring in a
anticlockwise direction,gently tightening it so the microphone or
XLR cable base is seated rmly in place.
To detach a microphone or a XLR cable
Turn the knurled ring in a clockwise direction, and pull o the
microphone or cable slowly.
Note: Please turn o the transmitter before attaching or removing
the microphone.
Connecting the Plug-on Transmitter and the Receiver
To connect the Plug-on Transmitter and the receiver, follow these steps:
1. Turn on the transmitter and the receiver.
2. Set the plug-on transmitter and the receiver to the same channel.
If you are experiencing interference or noise on one channel, try a
different channel.
NOTE:
For more details, please refer to “LCD Display Operation Guide”
on page 30.
1 2 3
CH-A-48
① )Channel Group (A/B
Long press “SET” botton to change ChannelA” or “B”
Channel number (1-48)
Battery indication
Mute On
IMPORTANT
1. The BY-WXLR8 Pro does not support external power supply.
2. Do not set the INPUT mold to MIC mold while the audio signal
is being input from the audio mixer, etc., it may cause excessive
audio input, resulting in distroted playback or recorded sound or
damage to playback or recording equipment.
3
4
5
6
7
2
8
9
Product Structure

Termékspecifikációk

Márka: BOYA
Kategória: mikrofon
Modell: BY-WXLR8 Pro

Szüksége van segítségre?

Ha segítségre van szüksége BOYA BY-WXLR8 Pro, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók mikrofon BOYA

BOYA

BOYA BY-PM700 Útmutató

14 Január 2025
BOYA

BOYA BY-WM3U Útmutató

31 December 2025
BOYA

BOYA BY-PM500W Útmutató

31 December 2025
BOYA

BOYA BY-M1000 Pro Útmutató

19 December 2024
BOYA

BOYA BY-PM700G Útmutató

9 December 2024
BOYA

BOYA BY-WM3D Útmutató

9 December 2024
BOYA

BOYA BY-PM700R Útmutató

9 December 2024
BOYA

BOYA BY-CM6 Útmutató

9 December 2024
BOYA

BOYA BY-CM6A Útmutató

9 December 2024
BOYA

BOYA BY-CM6B Útmutató

9 December 2024

Útmutatók mikrofon

Legújabb útmutatók mikrofon