Használati útmutató Bowers & Wilkins Performance Series CWM652

Bowers & Wilkins hangszóró Performance Series CWM652

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Bowers & Wilkins Performance Series CWM652 (3 oldal) a hangszóró kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/3
English
CWM6
5
4.2 If speaker cable is already present in the wall
space, pull the cable down through the aperture. If
speaker cables are not already installed this should be
done at this stage. It is likely that you will need to gain
access through the oor above to route the cables
down into the wall cavity.
Leave enough spare cable through the aperture to
ease connection to the speaker frame, but not so
much that it is likely to buzz or rattle when pushed
back up into the wall space. Approximately 1.0m (3 ft)
is appropriate.
Note: Always use high quality, low resistance
speaker cable. Low resistance is especially
important if the length of cable from amplifier to
speaker exceeds 5m. Your local Bowers & Wilkins
retailer will be able to offer advice on speaker cable
selection if required.
4.3 Now connect the speaker cable to the spring
terminals on the side of the frame. Ensure that the
speaker connection polarity is correct: the cable
connected to the positive terminal on the amplier
should be connected to the red spring terminal on the
frame. Similarly, the cable connected to the negative
terminal on the amplier should be connected to the
black spring terminal on the frame. The diagram above
illustrates cable connection.
Note: If an amplifier is already connected to the
cable it should be switched off while connections
are being made to the frame.
4.4 With the frame connected it may be inserted into
the wall aperture. Ensure that the QuickDogs™ (spring
clamps) are rotated so that they will pass through the
aperture then insert the frame up so that the ange
is ush on the wall. Take care that the cable is not
trapped. Now reach inside the aperture, rotate the
QuickDogs™ outwards and, using two ngers and
thumb, pull each spring clamp downwards so that the
frame is xed securely. There are four QuickDogs™ on
the CWM652 and six on the CWM663 and CWM664.
The diagram above illustrates insertion of the frame.
Note: To release a spring clamp push the metal tab,
located just below the finger platform, upwards.
4.5 If the frame ange is to be painted it should be
done at this stage. Any conventional, domestic paint
may be applied by brushing, rolling or spraying. Use
the supplied paint mask to avoid getting paint in the
cavity. Painting without using the paint mask risks
contamination of the internal connection terminals or
the grille attachment magnets. The diagram above
illustrates painting using the paint mask.
Note: If the grille is to be painted this should be
done “off-line” before it is fitted.
6
4.6 The bafe can now be tted into the frame. Ensure
that the connector on the bafe is oriented correctly
with the connector in the frame. The bafe is hinged
into place along its bottom edge and secured at the
top by two push-lock fasteners. Push-lock fasteners
are secured by pushing the head inwards – either
with a thumb or a screwdriver. Please ensure that
the largest groove on the fastener is orientated at a
diagonal, pointing to the corner of the bafe, before
pushing the fastener. As they secure, the fasteners
will click. The bafe will then be secure in the frame.
The diagram above illustrates inserting the bafe and
securing the push-lock fasteners.
Note: Push-lock fasteners are released by turning
anticlockwise with a screwdriver.
4.7 A three position high frequency level switch is
tted to CWM600 series models, on the front face of
the bafe. The centre position of the switch gives a
nominally level frequency response.
The HF+ boost position can be useful where the
listening environment is acoustically absorbent, for
instance where carpets, soft furnishings and curtains
predominate, or where the speakers are covered
by curtains or wall hangings. The HF- cut position
may be preferred where the listening environment is
acoustically reective, for instance where hard oors
and glass predominate. The diagram above illustrates
the level switch and its effect.
= 1x

Termékspecifikációk

Márka: Bowers & Wilkins
Kategória: hangszóró
Modell: Performance Series CWM652

Szüksége van segítségre?

Ha segítségre van szüksége Bowers & Wilkins Performance Series CWM652, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók hangszóró Bowers & Wilkins

Bowers & Wilkins

Bowers & Wilkins LCR3 Útmutató

16 Január 2025
Bowers & Wilkins

Bowers & Wilkins CWM664 Útmutató

16 Október 2024
Bowers & Wilkins

Bowers & Wilkins Nautilus 800 Útmutató

29 Szeptember 2024
Bowers & Wilkins

Bowers & Wilkins DM600 S3 Útmutató

24 Szeptember 2024
Bowers & Wilkins

Bowers & Wilkins CCM665 Útmutató

22 Szeptember 2024
Bowers & Wilkins

Bowers & Wilkins DM 604 Útmutató

20 Szeptember 2024
Bowers & Wilkins

Bowers & Wilkins CM1 Útmutató

14 Szeptember 2024
Bowers & Wilkins

Bowers & Wilkins 685 Útmutató

13 Szeptember 2024
Bowers & Wilkins

Bowers & Wilkins CCM664 Útmutató

12 Szeptember 2024
Bowers & Wilkins

Bowers & Wilkins DM602.5 S3 Útmutató

8 Szeptember 2024

Útmutatók hangszóró

Legújabb útmutatók hangszóró

Behringer

Behringer B2520 PRO Útmutató

10 Április 2025
Marshall

Marshall Willen Útmutató

10 Április 2025
JBL

JBL Control 426LP Útmutató

9 Április 2025
Crestron

Crestron SAROS IC8T Útmutató

8 Április 2025
LD Systems

LD Systems STINGER G3 TMB Útmutató

8 Április 2025
JBL

JBL Conceal C83 Útmutató

8 Április 2025
Crestron

Crestron SAROS ICE4T Útmutató

7 Április 2025
Crestron

Crestron SAROS ICI6T Útmutató

7 Április 2025
Focal

Focal K2 Power M FRAK Útmutató

5 Április 2025
Match

Match UP C42BMW-FRT.3 Útmutató

3 Április 2025