Használati útmutató Ballymore M-2000 144014
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Ballymore M-2000 144014 (3 oldal) a létra kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/3
14 0144
Ballymore Part # 4014 14
Inspect the ladder for shipping damage prior to starting asse y. If there is evidence of shipping damage n fy mbl oti
the carrier immediately.
STEP 1 - ASSEMBLE TOP STEP
- Place Stair Section (A) face down and attach Top Step (C) usi our washers (7) and locknuts (8). Tighten bolts ng f
completely
STEP 2 - ATTACH LOCKSTEP
- Attach Lockstep (B) to the bottom step using four washers (7) and locknuts (8 Tighten bolts completely. ).
STEP 3 ATTACH VERTICAL WELDMENT
- Align Low Vertical Weld G-1) & per Vertical Weldment (G-2) usi M8 x 60 bolts (6) with washers (7) er ment ( Up ng
and locknuts (8).
- Place Vertic Weldment (G) onto back of Stair Section (A) and align br kets o ent (G) al ac n top of Vertical Weldm
with Tabs protruding from bottom of Top Step (C).
- Us 25 bolts (2) with wa e (7) and locknuts (8) to fasten Vertical Wel ent (G) to Stair Section (A e M8 x sh rs dm ).
- Do not tighten bolts.
STEP 4 - ATTACH BASE WELDMENT
- Align Base Weldment (H) with the Tabs on the Front Legs of ladde Note : The cast s point up for this r. er
alignme nt.
- Use two M8 x 20 bolts (1) with washers (7), and locknuts (8) to fasten the Base Weldment (H) to the Front g Le s.
Do tighte not n.
STEP 5 - CO ECT BASE WELDMENT AND REAR VERTIC WELDMENTSNN AL
- Pivot weldments into position so the Angle Steel With Rigid Ca er and rear vertical conn t. Align the hole in the st ec
Angle Steel With Rigi aster with the hole in the base of the vertical and bolt together usi M8 X 50 bolts (5d C ng )
with washers (7) and lo nut(8). Ta care not to over tighten. ck ke
STEP 6 - INSTALL BRACES
- Install Vertical Braces (J), Horizontal Braces (K) and Diagonal Brace (L using M8 x 20 bolts (1), M8 x 25 bolts (2) )
and M8 x 50 bolts (5) with wa e (7) and locknuts (8). sh rs
If you purchased the All Directional Option ins ll it now, follow the directions included wi yta th our when kit
complete return to step 7
Get assistance to stand the ladder up. The easiest w to stand the ladder up is to rst lay side. Once ay it on it’s
the ladder had been stood up take it to a at su ace release the lock step dropping f nt legs of the ladder to the rf ro
ground. Make sure the ladder is rmly on the ground and tighten all bolts.
STEP 7- ASSEMBLE HANDRAIL CONFIGURATION CAREFUL WHEN ASSEMBLI HANDRAIL WE –BE NG –
RECOMMEND A SPOTTER TO ASSIST IN THIS STEP
- Bolt Rear drail (D) to the Top Step (C) using M8 x 20 bolts (1), washers (7) ocknuts (8). Guar and l
- nnect Top Handrails (E) to Rear Guardrail (D) using M8 x 40 bolts (3), wash s (7) and locknuts (8 Co er ).
Note : Handrail stiener should b ositioned on the outside of Stair Section (A e p ).
- Attach Handrail Bracket (I) to the Top Handrail i x 55 bolts (4), washers (7) a o nuts (8 Note : us ng M8 nd l ck ).
Handrail Brackets (I) sh ld be positioned on the inside of Stair Section (A Conrm Rear G drail (D) is ou ). uar
per endp i lar to the Top Step (C), and tighten the bolts. cu
- Mount Lower Handrails (F) usin andrail Brackets (I) and M8 x 55 bolts (4) and wa e (7), locknuts (8 Note : g H sh rs ).
Top of Lower ndrail ould butt against Top Handrail. Ha sh
- Tighten all hardware.
STEP 8 FINAL INSPECTION
- k to see that ladder sits level on oo After conrming that ladder sits level, tighten all hardware. Confirm all Chec r.
bolts have en properly tightene be d.
- ad instruction manual and become familiar with oper usa and maintenanc Re pr ge e.
- nnect instruction ma al to the ladder, insure all ers ad important safety information. Co nu us re
Ballymor Part #144 e 014
PARTS LIST
PART # DESCRIPTION QUANTITY
A STAIR SECTION 1
B LOCKSTEP 1
C TOP STEP 1
D REAR GUARDRAIL 1
E TOP HANDRAIL 2
F LOWER HANDRAIL 4
G-1 LOWER VERTICAL WELDME 1NT
G-2 P VERTICAL WELDME 1UP ER NT
H BASE WELDME 1NT
I HANDRAIL BRACKET 10
J R C BRACE 2VE TI AL
K HORIZONTAL BRACE 2
L DIAGONAL BRACE 2
M ANGLE STEEL WITH RIGID CASTER 1
1 BOLT X 10M8 20
2 BOLT X 4M8 25
3 BOLT X 4M8 40
4 BOLT X 20M8 55
5 BOLT X 4M8 50
6 BOLT X 2M8 60
7 WASHER 8 96
8 LOCKNUT 8 52
Termékspecifikációk
| Márka: | Ballymore |
| Kategória: | létra |
| Modell: | M-2000 144014 |
Szüksége van segítségre?
Ha segítségre van szüksége Ballymore M-2000 144014, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók létra Ballymore
19 Augusztus 2024
18 Augusztus 2024
18 Augusztus 2024
17 Augusztus 2024
16 Augusztus 2024
16 Augusztus 2024
15 Augusztus 2024
15 Augusztus 2024
15 Augusztus 2024
14 Augusztus 2024
Útmutatók létra
- létra JANDY
- létra First Alert
- létra Fieldmann
- létra Biltema
- létra Thule
- létra FireAngel
- létra Gre
- létra Foppapedretti
- létra Silverline
- létra Vonroc
- létra Altrex
- létra Brennenstuhl
- létra Hard Head
- létra Max
- létra Telesteps
- létra Kelfort
- létra Probuilder
- létra Batavia
- létra Cosco
- létra Krause
- létra Mr Safe
- létra GEV
Legújabb útmutatók létra
6 December 2024
27 Szeptember 2024
14 Szeptember 2024
8 Szeptember 2024
31 Augusztus 2024
30 Augusztus 2024
29 Augusztus 2024
28 Augusztus 2024
28 Augusztus 2024
28 Augusztus 2024