Használati útmutató Atdec A-STSCB

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Atdec A-STSCB (4 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/4
Lift Mechanism
Keyboard Tray
Keyboard PanelWork Surface
Support
Bracket
Clamp Plate
Keyboard Bracket
Clamp
Bracket Pressure
Plate
A
E
D
C
B
F
G H I
Spacer (x2)
Large Allen Key Small Allen Key Clamp Screw (x2) M6X8 (x10)
M6X12 (x10)M6X10 (x2) M6X35 (x2)
J K L M
ON P Q
Hardware
Installation Instructions
Sit-to-Stand Workstation
Desk Clamp
Step 1. Check components
Component Checklist
A-STSCB
IMPORTANT INFORMATION
! IMPORTANT - Install as per Installation Instructions
! This product is compatible with VisidecTM
Focus and SYSTEMATM monitor mounts.
! This product supports a total maximum load of 28.6lbs ( ). 13Kg
! The manufacturer accepts no responsibility for incorrect installation.
! Ensure any required electrical/data cables have sufficient length to accommodate the sit-to-stand workstation’s movement.
Check that you have received all parts against the Component Checklist.
Option 1
For desk thickness
less than 1.57” (40mm)
Option 2
For desk thickness
1.57” - 2.95” (40 - 75mm)
N
G
K
F
N
G
K
F
0 - 1.57”
1.57” - 2.95”
Desktop
Tighten
Firmly
!
Slide Clamp
onto rear edge
of desktop and
tighten the two
clamp screws
evenly.
Attach the clamp
screws and plate to
the clamp bracket
4.2
4.3
4.1
4.1
Step 4. Assemble Clamp
Step 2. Attach lift mechanism to work surface
Step 3. Attach keyboard bracket and tray
Lift Paddle
Alternate Position
The lift paddle can be
attached on the left or
right side of the work
station.
Cable Routing
Route the lift
paddle cable
through the slot in
the plates on the
lift mechanism (A)
3.1
3.2
3.3
AK
O
C
OO
Q
E
P
K
Lift
Paddle
K
D
K
B
K
M
Caution
Avoid pressing
the lift paddle
until Step 5.
7.1
7.2
Step 7. Attach lift mechanism to clamp plate
Step 6. Determine placement on desk
Step 5. Raise lift mechanism
Caution
When pressing
the paddle, the lift
mechanism will rise.
Keep clear as the
arm rises.
Adjust the position of the lift mechanism (A) on
the clamp plate (F) until the measurement shown
above is than or to less equal 13.8” (350mm).
Keyboard tray must clear the front edge of the
desktop when the workstation is lowered. ≤13.8”
Depress the lift paddle to
raise the lift mechanism.
K
K
M
A
F
I
M

Termékspecifikációk

Márka: Atdec
Kategória: nincs kategorizálva
Modell: A-STSCB

Szüksége van segítségre?

Ha segítségre van szüksége Atdec A-STSCB, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva Atdec

Atdec

Atdec AWM-AHX-S Útmutató

29 December 2024
Atdec

Atdec AWM-HN Útmutató

7 December 2024
Atdec

Atdec AWMS-NDB Útmutató

29 Augusztus 2024
Atdec

Atdec AF-AN-P Útmutató

19 Augusztus 2024
Atdec

Atdec AF-WD-P Útmutató

19 Augusztus 2024
Atdec

Atdec TH-VWP-160 Útmutató

19 Augusztus 2024
Atdec

Atdec AWM-HS Útmutató

19 Augusztus 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva